Plumbing 101: A Necessity for Bathtub Installation
Plumbing 101: A Necessity for Bathtub Installation
Blog Article
We've encountered this great article pertaining to Installing A Bathtub below on the net and thought it made sense to write about it with you on this page.
Setting up a bath tub isn't specifically brain surgery, yet it does call for solid plumbing, carpentry, and often, tiling abilities. Replacing an old bath tub with a brand-new one is additionally a reasonably difficult job. If the old tub is readily obtainable, the job can move easily; if you need to open a wall surface to eliminate the old tub and place the new tub, the task is a lot harder. In either instance, the job is within a house handyman's abilities, although you will need an assistant to move out the old bathtub and embeded in the brand-new one. Make sure you have qualified on your own for the job and also fit trying it. As opposed to working with a contractor to take over a halfway-completed job, it is much better to think about using one before you start. Chances are you may require a professional plumber to make tube links.
This write-up will certainly aid you set up a new bathtub in your shower room if you have currently bought a brand-new bathtub and also don't need to alter the arrangement of your previous water pipelines.
Your tools and material list must comprise the following:
Getting ready for the Installment
Firstly, the supporting framework provided with the bath needs to be fitted (if needed) according to the maker's instructions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is essential to see to it that if the tap comes with a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps device to prevent stress on the bathtub.
Fit the versatile faucet ports to the bottom of the two faucets utilizing 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make sure you make use of every one of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom ought to now prepare to be fitted in its final position.
Removing Old Touches
If you need to change old faucets with new ones as a part of your installation, after that the first thing you ought to do is separate the supply of water. After doing so, turn on the taps to drain any kind of water remaining in the system. The procedure of getting rid of the existing faucets can be quite problematic due to the limited access that is frequently the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the taps. Have a fabric ready for the remaining water that will certainly come from the pipelines. When the supply pipes have been removed, make use of the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming during this procedure. Once the faucets have been removed, the holes in the bath/basin will have to be cleaned of any type of old securing compound.
Prior to carrying on to fit the new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the brand-new taps to fit.
Installing the Bathtub
Making use of the two wooden boards under its feet, position the tub in the called for setting. The wood boards are practical in equally spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four tiny factors.
The following objective is to guarantee that the bath tub is leveled all round. This can be accomplished by inspecting the level as well as readjusting the feet on the tub until the spirit level reads degree.
To mount taps, fit all-time low of the furthest versatile faucet adapter to the proper supply pipeline by making a compression sign up with; then do the very same for the various other faucet.
Turn on the water system and check all joints and brand-new pipework for leakages as well as tighten them if required. Fill up the tub and additionally examine the overflow outlet and also the regular electrical outlet for leaks.
Finally, take care of the bathroom paneling as defined in the supplier's instruction manual. Tiling as well as sealing around the bath tub should wait up until the tub has been made use of a minimum of once as this will resolve it into its final position.
Suitable New Touches
If the tails of the new taps are plastic, after that you will require a plastic connector to avoid damage to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end provides a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making sure that the washing machines are in location between the tap as well as the sink. Protect the tap in place with the manufacturer given backnut. As soon as the tap is safely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular tap connectors. The former kind ought to be connected to the tap finishes initially, tightening only by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the location where the bath satisfies the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the installation can move enough to fracture a stiff seal, triggering the water to pass through the wall between the bath and also the tiling, resulting in difficulties with wetness and feasible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your fixtures and also installations. They are sold in tubes and cartridges, and are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of soaked newspaper or soft rope. Bear in mind to constantly load the tub with water prior to sealing, to permit the movement experienced when the bathtub is in usage. The sealant can crack relatively very early if you do not consider this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally conveniently available on the marketplace. It is a good idea to fit the tiles utilizing waterproof or waterproof adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed reading our excerpt on How to Install a Bathtub. Thanks a ton for taking a few minutes to read our blog post. So long as you enjoyed our page plz make sure you remember to pass it around. I am grateful for your time. Kindly stop by our site back soon.
Quality assurance? Connect. Report this page